Dirk Brenken [Sat, 26 May 2018 17:32:39 +0000 (19:32 +0200)]
luci-app-lxc: fix "plain-vanilla" integration, part 2
I've tried to get the lxc app in a more usable state. Tested with mips
and amd64 targets.
* check /etc/config/lxc in controller, not in cbi
* more controller cleanups
* remove unused 'fork_exec' function
* check path before container creation
* check space requirements before container creation
* support new uci options 'min_space' and 'min_temp',
default for both is 100000 KB
* both options are configurable via LuCI CBI template
* write messages to log in case of an error
* validate the container name during creation,
automatically remove invalid chars
* inform the user that only a stopped container can be destroyed
* add experimental ssl support (untested, disabled by default)
Dirk Brenken [Sun, 20 May 2018 17:23:53 +0000 (19:23 +0200)]
luci-app-lxc: fix "plain-vanilla" integration
I've tried to get the lxc app in a more usable state. Tested with mips
and amd64 targets.
* fix missing tar/xz dependency,
only if LXC_BUSYBOX_OPTIONS is not selected
* mute needless gpg validation warning
* tidy up controller a little bit
* fix multiple possible dispatcher errors
* fix compatibility with XHTML standard theme (looks still horrible ;-)
* inform the user about custom kernel prerequisites
* inform the user about the template download
* inform the user if no template was found
Jo-Philipp Wich [Sat, 19 May 2018 21:26:34 +0000 (23:26 +0200)]
luci-mod-admin-full: do not override iface section in wireless cbi map
Do override the iface section id upon commit to avoid clobbering the resulting
configuration. The manual config sync is not needed anymore after switching
to uncached ubus uci operations.
On certain environments, mainly with the embedded uhttpd interpreter, the
luci.config class cannot be loaded due to a circular dependency with the
luci.model.uci class.
Break up the dependency by deferring the loading of luci.config in
luci.model.uci until it is actually needed.
Florian Eckert [Wed, 9 May 2018 11:48:27 +0000 (13:48 +0200)]
luci-app-mwan3: pin diag ping command to interface device
If the physical device is not set in the diag_command then the ping will
always use the route with the lowest metric from the default routing
table.
To fix this add the physical device of the logical interface to the ping
command.
Florian Eckert [Wed, 9 May 2018 11:13:20 +0000 (13:13 +0200)]
luci-app-mwan3: honor dynamic interface to get gateway ip
If a logical interface setup and adds in the protocol handler a dynamic
interface then the gateway is configured in the dynamic interface and the
setting up logical interface does not have a gateway specified.
To fix this check first if a dynamic interface is present and use this
gateway ip if found and if no dynamich interface is set then check for a
gateway in the logical interface.
Dirk Brenken [Thu, 3 May 2018 05:53:48 +0000 (07:53 +0200)]
luci-app-travelmate: support new workflow & re-ordering fix
* Remove SimpleForm stuff from Interface Wizard
* adapt Travelmate to support new cbi apply workflow
* fix station re-odering
* tested successfully with old & new workflow
Florian Eckert [Tue, 20 Dec 2016 13:06:34 +0000 (14:06 +0100)]
luci-app-firewall: redirect to overview page on zone details save
This fixes an inconsistency because on the interface configuration if
you press Save&Apply it will go back to overview page. It is also the
case with "Firewall - Traffic Rules" details. On firewall zone it only
goes back to firewall zone-detail. Same behaviour on all pages is a good
user experience.
Florian Eckert [Wed, 29 Nov 2017 15:51:08 +0000 (16:51 +0100)]
luci-mod-admin-full: change supports_reset() test for factory reset
The check "supports_reset" only covers /proc/mtd partitions. If we have
this the commands checks for names like ubi or rootfs_data. If this is
found the system is possible for a factory reset. But on x86 the
situation is different. We have no /proc/mtd partitions because this
system do not use a bare metall flash.
To solve this issue check if we have an overlay and if so we could do a
factory reset. This could be applied for system which uses bare metal
flash and system which uses FTL or harddisks.
Jffs2reset is the current command used for factory reset. It will try
to find volume "rootfs_data" and if it's mounted will delete all files
under directory /overlay
luci-mod-admin-mini also has check for reset available, but we leave it
alone for now as it uses "mtd -r erase rootfs_data"
Florian Eckert [Wed, 22 Nov 2017 11:09:45 +0000 (12:09 +0100)]
luci-base: reload log on uci system change
If log configuration get changed in uci system no new values are applied
until reboot. Add /etc/init.d/log reload to exec option will solve this
issue.
Jo-Philipp Wich [Wed, 2 May 2018 08:37:02 +0000 (10:37 +0200)]
luci-base: add transitional /etc/init.d/ucitrack
Ship an /etc/init.d/ucitrack for spawning a virtual service with the sole
purpose to track the configurations and dependencies formerly handled by
luci-reload.
Once all LuCI supported services ship with procd compatible init scripts,
the uci track support can be dropped.
Jo-Philipp Wich [Tue, 1 May 2018 19:12:12 +0000 (21:12 +0200)]
luci-mod-admin-full: rework wifi configuration
- localize variables
- get rid of redirects breaking apply workflow
- auto-adjust unusable channels when switching country
- use apply/rollback workflow when enabling/disabling networks
Switch to rpcd based uci apply/rollback workflow which helps to avoid soft-
bricking devices by requiring an explicit confirmation call after config
apply.
When a user now clicks "Save & Apply", LuCI first issues a call to uci apply
which commits and reloads configuration, then goes into a polling countdown
mode where it repeatedly attempts to call uci confirm.
If the committed configuration is sane, the confirm call will go through and
cancel rpcd's pending rollback timer.
If the configuration change leads to a loss of connectivity (e.g. due to bad
firewall rules or similar), the rollback mechanism will kick in after the
timeout and revert configuration files and pending changes to the pre-apply
state.
In order to cover such rare cases where a lost of connectivity is expected
and desired, the user is offered an "unchecked" apply option after timing
out, which allows committing and applying the changes anyway, without the
extra safety checks.
As a consequence of this change, the luci-reload mechanism is now completely
unsused since rpcd uses ubus config reload signals to reload affected
services, which means that only procd-enabled services will receive proper
reload treatment with the new workflow.
Jo-Philipp Wich [Sat, 5 May 2018 20:56:30 +0000 (22:56 +0200)]
luci-mod-rpc: more auth/login fixes, expose further libraries
The previous attempt to fix authentication broke login functionality so
rework the code once again, this time with referencing helper functions
directly via the controller scope.
Furthermore, properly expose luci.sys.wifi.getiwinfo() and luci.ip.
For getiwinfo(), the RPC wrapped function accepts one further optional
parameter specifying the operation to invoke on the iwinfo instance.
If no operation is specified, a summary object containing all info
without country and scan list is returned.
Example to obtain iwinfo summary object:
curl --cookie sysauth=... \
--data '{"method": "wifi.getiwinfo", "params": ["wlan0"]}' \
"http://192.168.1.1/cgi-bin/luci/rpc/sys"
Example to obtain iwinfo scan list:
curl --cookie sysauth=... \
--data '{"method": "wifi.getiwinfo", "params": ["wlan0", "scanlist"]}' \
"http://192.168.1.1/cgi-bin/luci/rpc/sys"
The exposed luci.ip class uses a similar approach to allow invoking
instance methods on cidr objects. The new(), IPv4(), IPv6() and MAC()
constructors accept two further optional arguments, with the first
specifying the instance method to invoke and the second the value to
pass to the instance method.
Example to get list of IPv4 neighbours (ARP entries):
curl --cookie sysauth=... \
--data '{"method": "neighbors", "params": [{"family": 4}]}' \
"http://192.168.1.1/cgi-bin/luci/rpc/ip"
Example to add 100 hosts to a network address:
curl --cookie sysauth=... \
--data '{"method": "IPv4", "params": ["192.168.0.1", "255.255.255.0", "add", 1000]}' \
"http://192.168.1.1/cgi-bin/luci/rpc/ip"
Jo-Philipp Wich [Sat, 5 May 2018 17:51:20 +0000 (19:51 +0200)]
luci-mod-rpc: fix authentication via query string parameter
Localize the `authenticatior()` and `session_retrieve()` functions into the
`index()` function scope so that they're retained when extracting the
function into the dispatcher bytecode cache.
Also allow access to the global scope since upvalues do not work reliably
due to the out-of-context byte code caching of index functions.
Jo-Philipp Wich [Wed, 2 May 2018 14:52:37 +0000 (16:52 +0200)]
luci-mod-admin-full: canonicalize configured static lease MAC
When reading the configured mac address of the static lease, filter it
through luci.ip.checkmac() to canonicalize and uppercase the value for
mapping it against the combo box host hints.
git.99rst.org / openwrt-luci.git / log